2.4G Wireless Digital Camera 2.5" TFT LCD Baby Monitor

Features:

• Frequency: ISM 2,400~2,483MHz
• Receiver built-in Rechargeable Li-battery
• Receiving Sensitivity:-80dBm
• Brightness and Ratio option
• 2.5'' TFT LCD Display
• 4 Channel Wireless Receiver
• Resolution: 480 x 234
• Built-in Speaker
• Volume Control
• PAL/NTSC Receiver (Choose) AV line IN/ONT

Specification:

• 	ITEM	Value
  General	Transmission Frequency	ISM 2,400 ~ 2,483 MHz
  	Transmission Power	10mW/CE; 2mW/FCC
  	Unobstructed Effective Range	100m(Min.)
  	Spread Spectrum	FHSS
  	Modulation MODE	GMSK
  	Operating Temperature	-10OC ~ +50OC / +14OF ~ +122OF
  	Operatiing Humidity	15%~85%
  Camera	Imaging Sensor Type	CMOS
  	Picture Total Pixels	720 x 576(PAL) 720 x 480(NTSC)
  	Night Vision Distance	3m(Min.)
  	View Angle	40°
  	Sound Detection Sensitivity	>65dB
  	Consumption Current(Max.)	350mA
  	Power Supply	5VDC
  	Dimensions(W x D x H)	86 x 48 x 135 mm
  	Weight(About)	146g
  Receiver	LCD Screen Type	2.5”TFT-LCD
  	Effective Pixels	480×234
  	Receiving Sensitivity	=<-85dBm
  	Consumption Current(Max.)	200mA
  	Battery Working Time	5 hours
  	Battery Charging Time	5 hours
  	Power Supply	5VDC
  	Dimensions(W x D x H)	86 x 54 x 143 mm
  	Weight (About)	130 g

Installation:

• Locate the camera to a desired position and then adjust it to a suitable angle. 
  
  
• Connect the adapter to the camera 
  
  
  Tip: After the camera is powered on, touch the pole once with finger(s) to turn on the baby lights; touch again to turn off it; hold the pole and the lights will blink
• Install the accompanying Li-batteries to the battery compartment with its polarities matched. 
  
  
  Note: This receiver can also be powered on by adapter. The Li-battery will be charged after the adapter is plugged in, and the charge indicator lights in red during charging and will turn off after a full charge. A full charge will take about 5 hours, which can power the receiverfor about 2 hours continuously. You are recommended to have the battery fully charged before its first installation to optimize its life. Do not burn or disassemble the Li-battery. Do not short-circuit the battery, it may cause fire or electric shock.
• Slide the power switch to the ON position. 
  
  
• Tune the volume control to a desired level. 
  
  

CAMERA CHANNEL SETUP:

• The receiver supports up to 4 cameras working at the same time.Please set the channel switch on the back cover as the following diagram: 
  

CAUTIONS:

• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus
• Turn off the camera/receiver if the system is not in use
• The camera/receiver can only be completely disconnected from themains by unplug the adapter
• Do not cut the DC power cable of the apparatus to fit with another power source
• Attention should be drawn to the environment aspects of battery disposal

Packing Included:

• 2 x Wireless Camera
• 1 x Wireless Receiver
• 2 x AC Adapter For Camera
• 1 x AC Adapter For Receiver
• 1 x Lithium Battery For Receiver
• 1 x Video Cable